Specifications
|
Design |
Bookshelf or stand-mounted, 2-way active loudspeaker with DSP and discrete internal woofer and tweeter amplifiers |
|---|---|
|
Construction |
Primary enclosure: cast aluminum alloy with secondary machining Front baffle: extruded and machined aluminum |
|
Enclosure type |
Tweeter: sealed assembly Woofer: bass-reflex design vented at the base of the primary cast aluminum alloy enclosure |
|
Drivers |
Tweeter: carbon fiber dome, 26 mm (1 in.) Woofer: mineral-filled polypropylene cone, 140 mm (5.50 in.) |
|
Shipping weight |
41 kg (90 lb.) |
|
Net weight |
39 kg (82 lb.) |
|
Total continuous rated amplifier power, with less than 0.05% THD+N 1 |
400 W RMS |
|---|---|
|
Tweeter amplifier power |
200 W RMS at 6 ohms |
|
Woofer amplifier power |
200 W RMS at 6 ohms |
|
Analog to digital converters |
ESS™ SABRE® ES9822PRO (operating in mono mode) |
|---|---|
|
Digital signal processor |
AKM® triple-core with VELVET SOUND® technology processing at 32 bit/192 kHz for local system volume, crossovers, delays, equalization, and dynamics for each amplifier and driver section |
|
Processing bit depth/resolution |
32 bit / 192 kHz |
|
Crossover frequencies/slope |
3 kHz, 24 dB/octave Linkwitz-Riley |
|
Digital to analog converters |
ESS SABRE Reference DAC x 2 (operating in mono mode) |
|
Measurement engine |
Dual FFT measuring time, frequency and amplitude |
|---|---|
|
Measured results |
Frequency response (RTA, magnitude), impulse response (Lin IR, Log IR, ETC IR), and phase |
|
Computer requirements |
Computer running the Primacy Desktop application: Windows® 10 (OS Build 1809 or later), 11 Mac® OS 14, 15, 26 |
|
Power mode |
Off, Auto, or On |
|
|---|---|---|
|
Auto power mode |
Eco or Faster |
|
|
Lighting |
Off, Dim, or On Top panel accent light with user adjustable brightness levels. Displays active profile or user-defined color when connected to the Primacy centerpiece. |
|
|
Rear panel overridden |
LED indicates when the rear panel settings are disabled and under control by a connected Primacy centerpiece. |
|
|
Status |
Multicolor LED indicates the speaker's status and operating condition. |
|
|
Analog input grounding |
Grounded or isolated |
|
|
Analog input sensitivity |
Rotary dial with the following input signal voltages: 1: 8.0V (+18 dBV) 2: 4.0V (+12 dBV) 3: 2.0V (+6 dBV) 4: 1.0V (0 dBV) 5: 0.63V (-4 dBV) 6: 0.45V (-7 dBV) 7: 0.32V (-10 dBV) |
|
|
High-pass filter |
80 Hz @ 24 dB/octave (Off/On) |
|
|
Bass lift filter |
+3 dB shelving filter @ 117 Hz, Q=0.4 (Off/On) |
|
|
Treble cut filter |
-2 dB shelving filter @ 3780 Hz, Q=0.85 (Off/On) |
|
|
Output level trim |
Mute to 0 dB (-1 dB steps) |
|
|
Expansion port USB-C® DFU Reset |
Service controls ( Connections Panel Identification) |
|
|
Protocol |
Dante® audio over IP |
|---|---|
|
Standard |
IEEE802.3 compliant (1000BASE-T) |
|
Connections |
RJ45 x 2 (supports daisy chain speaker connections) |
|
Bit depth/resolution |
1CH @ 32 bit / 192 kHz |
|
Input impedance |
50 kohms |
|---|---|
|
Pin configuration |
Pin 1: shield Pin 2: positive Pin 3: negative |
|
Input Pin 1 ground lift |
Via Grounded/Isolated switch |
|
Analog input sensitivity at position 4 with level trim at 0 |
0.270 V |
|
Input impedance |
50 kohms |
|---|---|
|
Input ring ground lift |
Via Grounded/Isolated switch |
|
Analog input sensitivity at position 4 with level trim at 0 |
0.270 V |
|
Maximum peak short term sine wave acoustic output, averaged from 100 Hz to 3 kHz @ 1m, half space |
>112 dB SPL |
|---|---|
|
Factory target calibration |
Calibrated to achieve ±1.5 dB to reference response |
|
Anechoic frequency response |
55 Hz to 20kHz, +/- 2 dB, -3 dB @ 44 Hz, -6 dB @ 36 Hz |
|
Latency (at the speaker's analog input) |
4.46 ms |
|
Mains voltage |
100 to 240V AC, 50/60 Hz |
|---|---|
|
Power supply design |
Worldwide voltage compatibility with synchronized regulated switching power supply. |
|
Fuse type/value |
120V version: 5 A, 250V, 3AB fast acting, 0.25 in. ceramic cartridge 240V version: 3.15 A, 250V, 3AB fast acting, 5 x 20 mm glass cartridge |
|
Power cord |
Detachable IEC style 120V: 18 AWG, 10 A 240V: 17 AWG, 10 A |
|
Standby power consumption |
Auto power switch with Eco mode: <0.5 W Auto power switch with Faster: <7.0 W |
|
Idle power consumption (active with no signal) |
120V: approx. 34 W 240V: approx. 40 W |
|
Active power consumption (on with signal, 80 dB SPL. @ 1m, C-weighted) |
120V: approx. 35 W 240V: approx. 41 W |
|
12V Trigger |
12V DC input, 3.5 mm (1/8 in.) jack, tip positive 12V DC output, 3.5 mm (1/8 in.) jack, tip positive, 50 mA max. load |