Updates & Downloads

---

Edge 1030 software version 13.71 Beta

as of October 24, 2022

Download (18.77 MB)

View installation instructions and system requirements

Notes:

• Although this software is believed to be reliable, it has not yet been released for production and should be used at your own risk.

---

Change History

Changes made from version 13.50 to 13.71:

• Added RCT715 recording status indicator.
• Added support for saving photos and video clips on the RCT715 when the camera is disabled or busy.
• Added support for turning off RCT715 video recording when suspending or powering off the Edge.
• Updated to CIQ API version 3.3.6.
• Fixed issue where connectivity firmware would cause the device to freeze.
• Fixed potential device freeze when importing read-only GPS files
• Fixed issue where courses with no recorded elevation data would result in a blank ClimbPro elevation profile.
• Fixed issues with indoor trainer controls in ERG and manual modes.
• Fixed time zone offset when syncing time with the phone without a valid time from GPS.
• Fixed issue where ephemeris status would incorrectly be displayed as expired.

Changes made from version 13.28 to 13.29:

• Fixed an ANT burst-mode issue.

Changes made from version 13.26 to 13.28:

• Added support for Connect IQ System 5.
• Improved map turn review zoom level when approaching roundabouts at slow speeds.
• Fixed issue where very long course names resulted in routing calculation failure.
• Fixed issue where activities could be hidden from history.

Changes made from version 13.24 to 13.26:

• Fixed software crashes caused by encrypted CIQ programs that are no longer valid.
• Fixed a couple of device stability issues.

Changes made from version 13.22 to 13.24:

• Fixed automatic maximum heart rate detection.
• Added the ability to perform the FTP test with power data coming from a trainer.

Changes made from version 13.20 to 13.22:

• Changed gear battery data field to display percentage remaining if available, which affects Shimano Di2 single-battery systems.
• Updated sensor low battery prompts to differentiate between low and critical status.
• Fixed issue where distance could stop accumulating.
• Fixed issue where text message sender names would display incorrectly.

Changes made from version 13.10 to 13.20:

• Fixed issue causing VO2 max to not be calculated and performance condition from working.

Changes made from version 13.00 to 13.10:

• Fixed issue introduced in a recent public beta where the ANT search channel could remain open for the whole ride causing potential connectivity issues and draining battery unnecessarily.

Changes made from version 12.63 to 13.00:

• Fixed Back to Start issue when selecting Most Direct Route
• Fixed issue where LiveTrack could not be started
• Added a routing avoidance setting for interstate highways that allow bicycles. Previously, a user could not create a cycling route on interstates, even if the interstate allowed cycling.

Changes made from version 12.20 to 12.63:

• Fixed device-to-device transfers
• Added new tone for radar that that plays when your radar transitions to the green threat level. Go to the radar settings in the sensors menu to enable this feature.
• Improved bike light network connection stability
• Improved course point display and added new types
• Improved Course 'Always Show' functionality
• Improved shifting sensor battery data fields
• Improved Physio True-up data recording
• Improved indoor trainer control
• Fixed issue causing unnecessary sensor software update prompts
• Fixed power calibration prompt when waking from sleep mode
• Fixed history line color
• Fixed issue with left/right power balance recording
• Fixed issue with GPS not turning off in indoor mode
• Fixed the power graph during workout steps with no power target
• Improved general device stability

Changes made from version 12.00 to 12.14:

• Fix issue with Fazua BLE scanning
• Fix crashes drawing third party maps
• Fix issue unlocking maps from SD card

Changes made from version 11.23 to 11.24:

• Fixed a crash when calculating course routes.
• Fixed an issue with calculating course routes on 3rd party maps.

Changes made from version 11.19 to 11.23:

• Fixed various issues with course routing.
• Fixed issues with indoor course mode.
• Fixed issue with blank Strava segments appearing on the Segment Explore widget.
• Fixed Browse Map panning.
• CIQ
  Improved CIQ data field settings experience by always prompting when adding a settings-capable CIQ data field.
  Increased font size for app background messages.
  

Changes made from version 11.10 to 11.19:

• Course Routing
  Improved course routing speed.
  Added automatic course route caching.
• Map
  Improved map visibility and contrast with new map themes.
  Added a popularity layer to highlight roads that Garmin users have ridden the most.
  Added directional arrows to routes, courses, and history lines.
• Phone
  Added smart syncing before an activity.
  Added a Sync Now button to the settings widget and the Connected Features > Phone menu.
• Updated Firstbeat library for various improvements and bug fixes including a fix for training stats being reset on a multiple day activity.
• CIQ
  Fixed issue with BLE sensors in CIQ data fields after waking the Edge from sleep mode.
  Fixed issue where activity controls would not work in a CIQ app.
  Fixed other minor issues.
  
• Fixed several inReach issues.
• Improved Garmin dual-mode sensor management.
• Improved power meter calibration and software updates.
• Improved the cycling dynamics page.
• Increased maximum number of workout steps from 50 to 100.
• Combined the indoor trainer Target Power and Resistance data fields into a single new 'Trainer Mode Value' data field that will dynamically change the title and value based on the current trainer mode between Target Power, Slope, and Resistance options.
• Added support for including metabolic calories in the total calories reported in the calories data field and recorded in the activity file.
• Fixed manual elevation calibration.
• Fixed minor bugs.
• Improved device stability.

Changes made from version 10.25 to 10.26:

• Removed radar all-clear tone.
• Fixed crash on power down and going to mass storage mode.

Changes made from version 10.22 to 10.25:

• CIQ 3.2
  Added encryption for CIQ widgets and data fields.
  Added CIQ workout information support.
  Added CIQ data field alerts.
• Improved radar all-clear tone user experience.
• Added tone to end of FTP test to notify user of completion.
• Fixed FTP test preview page showing incorrect data.
• Fixed crash on map data screen layout configuration.
• Fixed various other crashes.

Changes made from version 10.20 to 10.22:

• CIQ 3.2
  Added CIQ 3.2 support.
  Added BLE sync support for the Connect IQ app.
• Indoor Training
  Added smart trainer widget that includes Tacx Road Feel controls.
  Fixed course points for indoor trainer rides.
  Added the Virtual Partner to the map page when following course or activity on indoor trainer.
  Fixed issues with grade, power, and resistance controls for smart trainers.
• Simple Setup
  Added Simple Setup support. Port old activity profiles and sensors from Garmin Connect during initial setup.
• Livetrack
  Added device driven Livetrack.
  Added course sharing.
• Radar
  Added radar 'All Clear' tone. Setting is configurable in the radar sensor setting menu.
  Added instructions for pairing a radar in the radar sensor search menu.
• Segments
  Fixed recurring 'Deleting Segments' prompt.
  Fixed updating segment leaders on sync.
  Fixed segment completion bugs.
• Improved reliability of FTP auto detection.
• Fixed segment completion bugs.
• Fixed crash when updating sensor software.
• Fixed issue with smart eat and drink alert prompts.
• Fixed false 'Climb Complete' prompts when riding a segment with ClimbPro.
• Fixed retaining light network disable over power cycle.
• Added support for metabolic calories in the activity file.
• Fixed other minor UI bugs and crashes.

Changes made from version 9.50 to 9.68:

• Segments
  Fixed issue with detecting segments that were going in the opposite direction of travel
  Improved segment and ClimbPro UI cooperation
  Fixed issues when approaching a segment embedded in a course and other minor segment UI issues
  Fixed issue where segment virtual partners would claim to be finished almost immediately after starting the segment
• ClimbPro
  Improved estimated time to end of a ClimbPro climb
  Fixed ClimbPro page graph drawing
  Fixed issue where disabling 'Pop-up on Climb Approach' would disable ClimbPro completely
• Improved iPhone pairing
• Improved sensor connectivity
• Improved automatic FTP detection
• Added Go Back, Pause, and Go Forward workout step controls to the workout tray
• Added support for new GPS firmware. Sync your device to update to the new firmware
• Added option to delete a data field in quick edit mode. Access by pressing and holding a data field on a timer page.
• Improved grit and flow consistency between Garmin products
• Improved bike light connection stability
• Fixed bike alarm not turning off after correct password was entered
• Fixed radar vehicle drawing temporarily not updating
• Added a shortcut to the display menu by pressing and holding the Auto Brightness button on the status widget
• Added a toggle for MTB map theme
• Improved MTB trail search UI
• Fixed issue where history line wasn't updated while panning in the map
• Fixed issue with the number of power zones displayed post ride
• Fixed dual sided power meter calibration factor reporting only one side
• Fixed Firstbeat metrics for multiple rides during the same power cycle
• Fixed Training Effect UI layout
• Removed unnecessary beeps for notifications that don't need them
• Fixed timezone map downloads from WiFi
• Fixed issue with power targets in TCX workouts
• Made various device stability improvements

Changes made from version 9.44 to 9.48:

• Fixed an issue with sensor connectivity.
• Added diagnostics to help track down an issue where the device can lock up.

Changes made from version 9.34 to 9.44:

• Added diagnostics to help track down an issue where the device can lock up.

Changes made from version 9.31 to 9.34:

• Fixed a crash on the keyboard page.
• Fixed an issue that caused bike radar disconnections.

Changes made from version 9.28 to 9.31:

• Fixed an issue with sensors dropping out.
• Fixed an issue where the device could become unresponsive.
• Fixed an issue where ascent remaining was not properly calculated for segments embedded in a course.
• Allow the elevation profile setting on the map to be maintained through future software updates.

Changes made from version 9.26 to 9.28:

• Made stability improvements including a fix for a potential device freeze.

Changes made from version 9.25 to 9.26:

• Fixed an issue where saved location names were drawn incorrectly on the map in night mode.
• Fixed invalid Grit/Flow values appearing on the activity lap summary.

Changes made from version 9.24 to 9.25:

• Fixed an issue with 12-speed gear shifting systems.
• Fixed the Indoor Trainer 'Remind Me' prompt to ensure it does not prompt again if the user declines the reminder.
• Changed the trainer resistance data field title to Grade for better clarity.
• Modified the prompt for LiveTrack auto start timeout to occur at most once per activity.
• Fixed an issue with ClimbPro where some short climbs were not detected.
• Fixed layout issues introduced on the Bike Lights widget.
• Fixed an issue that caused POIs to show incorrect bearing and distance.
• Only show Grit and Flow in the activity summary if they are valid.
• Added letters to the Polish keyboard support Wi-Fi passwords that require non-Polish characters.
• Fixed an issue that could keep the device from fully entering suspend mode.

Changes made from version 9.10 to 9.24:

• Indoor Riding Improvements
  - Added the ability to set system time using WiFi or Bluetooth when GPS is not available.
  - Added a Free Ride indoor trainer mode that enables the trainer to be set to a target grade.
  - Added a 'Remind Me' prompt for the trainer search.
  - Made a change so LiveTrack is not started automatically for indoor or virtual activities.
  - Prevent light network from forming indoors.
• Elevation and ClimbPro Improvements
  - Added grade coloring to the elevation chart.
  - Added grade coloring for segments.
  - Changed the Time to Destination data field to show estimated time to the top of the climb if ClimbPro is activated.
  - Fixed an issue with cumulative ascent and ClimbPro not working properly when a course is transferred from Garmin Connect.
  - Fixed incorrect category colors on the ClimbPro page.
• Made Mountain Bike feature settings available in all activity profiles to allow for Grit, Flow, and Jump data metrics to be enabled if desired. These remain turned off by default for all non-MTB profiles.
• Added the ability to configure the minimum ride length that should prompt for Nutrition/Hydration intake.
• Added the ability to customize the activity track color on the map.
• Fixed an issue where the device could falsely report that it was fully charged after coming out of suspend mode.
• Fixed an issue where GPS satellites were lost more often than they should be.
• Improved Bluetooth friendly names to include BLE and BT so they can be distinguished from each other.
• Fixed an issue that could cause unit-to-unit transfers to fail.
• Fixed an issue with OSM roundabouts giving incorrect guidance.
• Fixed an issue where the Course Creator out-and-back was not working properly.
• Integrated the ability to use cached weather data for Firstbeat analysis.
• Updated the turn review map page so the distance on the top left of the screen updates and the data field on the bottom left shows Heading.
• Made OK the first response for LiveTrack and Text Message response prompts to minimize interaction while riding.
• Improved the Reset HR Zones and Reset Power Zones behavior to only reset the zones and not the Max HR value or FTP.
• Made it easier to switch between the month/week view in the Training Plan calendar page.
• Fixed the alert sound not working when a workout is complete.
• Fixed false level of timer precision on Garmin segments.
• Fixed handling for long course names.
• Fixed an issue that could cause the device to lock up.
• Fixed ANT+ shifting data not being correctly written to FIT files.

Changes made from version 9.02 to 9.03:

• Fixed an issue where sensors would not connect to Connect IQ data fields after powering on the device.

Changes made from version 9.00 to 9.02:

• Fixed an issue that could cause instability when using Connect IQ apps and data fields.
• Fixed an issue where data could be missing from segment FIT files.

Changes made from version 8.08 to 8.11:

• Improvements for Indoor activities
  - Fixed an issue where sensors did not automatically re-pair in indoor activity profiles.
  - Fixed indoor rides reporting incorrect time when following a course from a different time zone.
  - Indoor activities now report elevation properly when following a course.
  - Indoor activities recorded while following a course or previous activity are now shown as Virtual Cycling on Garmin Connect
• Fixed an issue that kept the workout graph from appearing on the Training Plan screen.
• Fixed a shutdown when using BLE sensors.

Changes made from version 8.07 to 8.08:

• Fixed an issue where activities could report inaccurate distances if GPS was acquired after the activity started.
• Fixed an issue where only a single sensor of each type was shown in the Search All list.
• Fixed an issue with the Trainer Found prompt appearing too often.
• Added map and elevation data screens to indoor profiles when a course is active.
• Updated the segment leaderboard strings to be more descriptive.
• Fixed an issue where the back button had unexpected behavior in some Connect IQ apps.
• Fixed a crash related to BLE sensor connection.
• Fixed a crash related to ClimbPro.

Changes made from version 8.06 to 8.07:

• Fixed an issue with pairing to iPhone 11.
• Fixed a shutdown related to using Connect IQ data fields.
• Fixed a shutdown on the inReach widget.
• Fixed an issue where ClimbPro could report inaccurate information.

Changes made from version 8.00 to 8.06:

• Added support for Connect IQ 3.1.
• Added support to control Garmin inReach remotely.
• Made improvements to indoor cycling user experience.
  - Improved smart trainer discovery and initial setup experience when using an Indoor activity profile.
  - Improved the Follow Course experience by enabling UI (map, ClimbPro, Elevation, etc) and data recording from the simulated course.
  - Made improvements to smart trainer sensor calibration.
• Made improvements to Workout user experience.
  - Added FTP line to workout comparison displays.
  - Allow graphical workout data fields to be configured on regular data screens.
  - Improved the display for open steps on the workout comparison graph.
• Made improvements to the ClimbPro user experience.
  - Made ClimbPro available for navigation to a location and for round-trip courses.
  - Added a setting in the ClimbPro data screen setup to specify which climbs should be detected (All, Medium/Large, Large Only).
  - Removed the ClimbPro page from the timer loop if there are no climbs left in the ride.
• Made improvements to the Segment user experience.
  - Fixed an issue where segments with slashes in the name would not be processed and would create subfolders on the file system.
  - Fixed an issue where the segment leader could get reset during a sync.
  - Added setting in the Segments menu to set a Default Leader Priority, which allows the user to set a default leader to apply to all segments.
• Fixed an issue where the GPS track locked to the road inaccuarately.
• Improved Firstbeat heat acclimation by utilizing weather forecasts.
• Fixed an issue where Battery Save Mode could stop working mid-ride.
• Show the jump prompt for each jump in cases where there are multiple jumps in a row.
• Fixed issues with the heart rate graph data field.
• Fixed an issue that caused Auto Detect Max HR to always be enabled.
• Improved the y-scaling on the elevation profile.
• Added directional arrows for round trip courses.
• Fixed cosmetic issues with Extended Display mode.
• Added additional info to the nutrition/hydration settings page
• Turned backlight on when the user laps or there is an autolap during an activity
• Automatically sized the text in the elevation data field.
• Improved overall device stability by fixing crashes and freezes.

Changes made from version 7.85 to 7.87:

• Fixed an issue where activity profiles could be lost during a software upgrade
• Fixed crashes that could occur during a workout when transitioning steps
• Fixed issue where trying to discard an activity while sitting on the elevation page would cause the activity to be retained
• Fixed the initialization of the widget management feature if a user already had a Virb or Light paired
• Fixed several crashes caused by WiFi operation
• Fixed auto-brightness responsiveness
• Updated the My Stats Training Status pages to better fill the screen
• Improved device stability

Changes made from version 7.50 to 7.85:

• Training Load Focus. Low Aerobic, High Aerobic, and Anaerobic stats are tracked over a 4 week window and the user should be able to track what needs to be focused on.
• Two-way setting sync. Changes to some settings made on the Edge (zones, user profile, etc) will now be uploaded to Garmin Connect.
• Heat/Altitude Acclimation. Shows user's acclimation to different altitudes and hot/humid environments.
• ClimbPro. See upcoming climbs while riding a course so you can prepare for needed effort
• Power Curve tracking has been added to the My Stats menu.
• Nutrition/Hydration tracking alerts
• Training Plan Review Page Improvements
• Workout Comparison Graph. Provides live feedback while executing a workout.
• Widget Management. Disable and re-order items in the widget loop
• Bike Theft Alarm*. While armed, get alerted when your Edge device moves.
• Find My Edge*. Help find a misplaced Edge by making it beep or showing its last known location on your phone.
• Grit/Flow**
• Jump Metrics**
• Added a new Popular data field category and generally improved the data field category order
• Updated screen creation and editing flow (applies to eBike/STEPS, Lap Summary, Segment, and Data Screen)
• Ability to swap data fields while in the timer loop on long press instead of edit only (additional tap required)
• Updated battery icon to be more visible in some places
• Incident detection setting is now active per profile instead of globally
• Added ability to hide data screens without deleting them
• Reordered settings to match the Edge 830, mainly splitting the growing number of settings into Safety & Tracking (Incident Detection, Get Assistance, Contacts, GroupTrack, Bike Alarm) and Connected Features (Phone, WiFi, Device Transfers)
• Additional small changes and improvements
• * Complete functionality requires an upcoming Garmin Connect Mobile release
• ** Mountain Bike Profile Only

Changes made from version 7.41 to 7.42:

• Fixed issue where CIQ data fields were removed every power cycle.

Changes made from version 7.40 to 7.41:

• Added the option to choose the radar alert tone.
• Added support for Shimano STEPS 2.1.
• Added eBike activity logging.
• Fixed issues with the cycling dynamics page.
• Fixed issue where two locations with long, similar names would cause the device to crash.
• Fixed issues with loading very long courses.

Changes made from version 7.20 to 7.22:

• Fixed a crash that could occur when riding with a cadence sensor.

Changes made from version 7.00 to 7.07:

• Improved connection to the Edge Remote.
• Fixed issue causing Connect IQ MapView to not handle inputs.
• Fixed incorrect navigation audio tones from the 7.00 update.
• Fixed a crash when sending GroupTrack messages.
• Added support for 12-speed shifting systems.
• Fixed data field issues when using a shifting system with no front derailleur.
• Fixed crash when doing the FTP test.
• Updated RTL510 and RTL500 light modes for Auto and Trail modes.
• Fixed Varia lights not activating when starting an activity.
• Fixed issue where radar would not automatically reconnect after being disconnected for more than 2 minutes.
• Fixed issue where the Edge would not automatically pair with a radar that is paired to a watch that the Edge is connected to via Extended Display Mode.
• Made several improvements to the Sensor Details UI for Vector 3 power meters.
• Added support for displaying eBike data fields on a Varia Vision.
• Fixed bug in Extended Display mode where Di2 battery would report as 255%.

Changes made from version 6.45 to 6.46:

• Fixed several crashes that could occur while riding with a power meter.
• Fixed segment updates.
• Fixed issue where the GPS data field did not match the GPS indicated by the status bar.

Changes made from version 6.44 to 6.45:

• Fixed Favero Assioma data dropouts.
• Updated radar tone to be easier to hear.

Changes made from version 6.43 to 6.44:

• Fixed elevation zooming issue with large courses/activities/segments (>100mi or km).
• Fixed ANT sensor battery low notifications.

Changes made from version 6.30 to 6.43:

• New Beta Feature: Galileo satellites. There is now support to use the Galileo network of satellites to assist in getting GPS fixes. With the correct GPS firmware, this option can be enabled by selecting GPS+Galileo in the GPS setting. Sync the device with Garmin Express to make sure that the new line of GPS firmware is provided to the device. Without this, the option will not be available.
• Added support for ANT+ cycling dynamics metrics.
• Updated smart notification categories. In the phone settings, social and other smart notification categories can be enabled. This will make the Edge show notifications from other applications depending on how they are categorized by Garmin Connect Mobile. Apps like WhatsApp, GroupMe, and Twitter may show up under social and things like e-mail, calendar, and news may show up under other. These categories are off by default and must be enabled to be seen.
• Fixed an issue causing cadence and power data dropouts.
• Fixed the activity profile routing mode getting reset to Road Cycling mode.
• Fixed issues with device transfers.
• Added prompt to indicate when a course has more course points than are supported by the device.
• Improved Shimano STEPS response time.
• Fixed lens mode VIRB setting.
• Fixed issue with transmitting front and rear gear information to the Varia Vision.
• Fixed sharp bend notifications on the Varia Vision.
• Fixed issue with elevation back correction that could allow large dips in elevation.
• Added the current software version to the power on page.
• Completing a segment will now turn on the backlight.
• Added a minimum scale to the altimeter page so that small elevation ranges are reflected properly.
• Improved activity auto-start when the device is stationary.
• Minor bug fixes and stability improvements.
• Minor CIQ improvements.

Changes made from version 5.28 to 5.33:

• Fixed a potential freeze when powering off.
• Fixed CIQ custom fonts.
• Fixed several CIQ Menu2 issues.
• Fixed an issue that could prevent a radar low battery message from displaying.

Changes made from version 5.27 to 5.28:

• Fixed an issue causing freezes when powering down introduced in 5.27.
• Prevented crashes caused by adding new segment files during an activity.
• Fixed issues with elevation units on the Varia Vision.
• Added the ability to add CIQ data fields to the map data screen.
• Fixed issue where auto backlight could activate despite the setting being turned off.
• Fixed a light settings vulnerability that could cause the light settings to not be saved.

Changes made from version 5.00 to 5.27:

• New Feature: Added Connect IQ 3.0 support.
• New Feature: Added Shimano STEPS sensor support.
• New Beta Feature: Added extended display mode support. Select Menu > Extended Display Mode to allow the Edge device to act as an extended view of a supported Garmin multisport watch's data fields during a multi-stage activity such as a triathlon. Follow the on-screen Edge and multisport instructions to get started.
• Improved sensor searching flow.
• Fixed issue causing unexpected u-turn sharp bend warnings.
• Fixed issues preventing device-to-device transfers from completing and made improvements to the connection flow.
• Fixed various issues with the Varia Vision.
• Fixed issue with Physio TrueUp duplicate activity detection.
• Fixed issue where VO2 max could be corrupted.
• Fixed issue that could cause the device to crash while connected to the phone.
• Fixed bike light beam angle and light mode data field text.
• Fixed the Follow a Course flow for indoor trainer mode.
• Fixed issue with the device where going into mass storage from a power off state may cause Garmin Express to offer a map update that the device does not need.
• Improved Physio TrueUp responsiveness by syncing with the phone after powering up or resuming from suspend.

Changes made from version 4.24 to 4.36:

• Added Physio TrueUp support. Physio TrueUp syncs activities done on other Garmin devices, allowing your device to more accurately reflect your training status and fitness. Activities from other devices will appear in the History menu. Your Training Status, Training Load, and VO2 Max will be updated using activities from your other devices, and your Recovery Time will be also updated using data from other devices supporting Physio TrueUp. Enable Physio TrueUp in Device Settings on Garmin Connect or Garmin Connect Mobile.
• Improved BLE stability. This should address issues with LiveTrack not working properly and with BLE sensors freezing.
• Fixed issue with 2018.10 maps where turn prompts may be missed during navigation.
• Fixed an issue that could cause software updates to clear the list of paired sensors.

Changes made from version 4.11 to 4.24:

• Fixed a crash when racing a rival effort on a segment with a long name.
• Improved text message notifications by removing the requirement for Garmin Connect Mobile to have Android SMS and Contacts permissions.
• Added support for receiving and replying to texts from other providers (e.g. Facebook, Google Hangouts).
• Fixed crash when using audio prompts.
• Fixed incorrect sharp bend warnings when riding on a course.
• Fixed misaligned text when performing an address search.
• Note: This public beta does not address the BLE and LiveTrack issues that have been reported with 4.00. We will provide another update as soon as the issues are resolved.

Changes made from version 4.01 to 4.11:

• Fixed issue causing saved locations to be deleted from memory.

Changes made from version 4.00 to 4.01:

• Fixed issue preventing the device from connecting to Garmin BaseCamp.

Changes made from version 3.90 to 3.97:

• Added enhanced support for Varia RTL510 radar tail light.
• Updated touchscreen firmware to 85.11 to improve responsiveness in low temperatures.
• Added CIQ 2.4.4 support.
• Improved device stability.
• Added the ability to discard the current ride at any time. This requires several interactions to avoid accidental discards.
• Fixed text conversion issues.
• Fixed issues with the Varia Vision data screen setup causing the Edge and Varia vision to be out of sync.
• Fixed issue preventing a BLE sensor from being added if it was the first sensor.
• Fixed issue where the ANT generic channel used by CIQ data fields would not reconnect when the device resumes from sleep.
• Fixed issue where battery save mode would turn on GPS in the Indoor activity profile.
• Fixed issue preventing some iPhones from staying connected during the pairing process.
• Fixed issue where the ascent remaining and ascent to next course point data field values did not match the total ascent for the course.
• Fixed several issues with sharp bend warnings.
• Fixed issue where FTP would be reset after recording an activity with a CIQ app.
• Fixed issue preventing battery save mode if the timer is auto-paused.
• Fixed issue where calories would be incorrectly calculated for BLE power meters.
• Fixed navigation audio prompts.

Changes made from version 3.82 to 3.85:

• Improved Bluetooth pairing/connection for Huawei phones.
• Improved device stability.
• Added battery status to power on page.
• Fixed Lap Normalized Power data field.

Changes made from version 3.80 to 3.82:

• Improved device stability.
• Fixed Round-Trip Course issue where ferries and tolls avoidances were being ignored.
• Fixed bike light controls on the bike lights widget to send the appropriate light mode to any light.
• Improved elevation profile scrolling.
• Added the ability to add up to 10 custom data screens.
• Added CIQ 2.4.2 support.
• Fixed CIQ system fonts.

Changes made from version 3.74 to 3.77:

• Improved temperature reporting.
• Fixed an issue where closing GCM on iOS would break the connection with the Edge.
• Fixed an issue allowing BLE to remain on after disabling the phone setting on the Edge.
• Fixed issues introduced in 3.74 with importing and remerging courses.
• Fixed an issue introduced in 3.74 causing Bluetooth instability and device shutdowns.

Changes made from version 3.70 to 3.74:

• Improved Bluetooth connectivity.
• Improved Edge remote connectivity.
• Fixed issues with Device Transfers.
• Fixed issues with editing power zone values.
• Enabled turn-by-turn navigation support for courses imported from GPX tracks.
• Increased automatic screen brightness in low-light conditions.
• Fixed issue preventing anti-aliased CIQ fonts.
• Fixed issue where segments were not blocked while using CIQ apps.
• Fixed issue where the widget indicator bar would not fade away while viewing a CIQ widget.
• Fixed units sync with the Varia Vision.
• Fixed issue with elapsed time when the timer is paused.
• Improved sharp bend warnings.
• Improved device stability.

Changes made from version 3.60 to 3.61:

• Fixed Connect IQ arc drawing.

Changes made from version 3.50 to 3.58:

• Added sharp bend notifications while not navigating.
• Added Connect IQ 2.4.1 support.
• Added Wi-Fi support for Strava Segment Explore.
• Added VIRB camera widget and VIRB 360 settings support.
• Fixed Training Effect inaccuracies, Training Load peaks that were over-inflated, and the Stress Score feature.
• Fixed issue where segments would not display on the map and allowed the Segments activity profile option to control whether segments display or not.
• Fixed issue where the Edge would not receive sensor software updates.
• Fixed issue causing erroneous GPS position on iPhone.
• Improved graphics performance.
• Made stability improvements.

---

Installation Instructions

1. Connect your Edge 1030 device to your computer using the micro-USB cable.
2. Download and unzip Edge1030_1371Beta.zip and place the GUPDATE.gcd file in the \Garmin folder of your device's internal storage drive.
3. Disconnect your device from the computer, approve the update on the Edge, and wait for the update to finish.
4. If you would like to revert to the last public release software, follow the above steps but place the GUPDATE_1350.GCD file in the \Garmin folder. Rename the file to GUPDATE.GCD before disconnecting your device.
   NOTE: If you revert to an older version of software, all of your settings will be reset to defaults.

---

System requirements

1. IBM-compatible PC running Windows 2000 or later operating system and an available Com 1, 2, 3, or 4 port.
2. PC Interface Cable for your GPS unit. The PC Interface Cable may be purchased through your local Garmin distributor or ordered direct from our Online Store.

---