Updates & Downloads

Rino 110 software version 3.90

as of July 5, 2006

Use Garmin Express to install this file.

(845 KB)

View system requirements

Notes:

WARNING: If you are updating from a version less than 2.10, this software update will clear user memory. Please back up important data to MapSource.
WARNING: If this software is uploaded to a device other than that for which it is designed, you will not be able to operate that device.
If attempts to upload software fail, you may need to return the device to Garmin® for service.
Note: This software is only compatible with the following previous versions: 2.00 - 3.80

Change History

Changes made from version 3.80 to 3.90:

Correctly displays position field while it is being edited.

Changes made from version 3.70 to 3.80:

Adds 9600 baud and faster update rate options to NMEA in/out mode.
Updates WAAS/EGNOS satellite search and selection process.
Correctly remembers serial interface settings between power cycles.
Applies map datum only to the Location (selected) field and not to the Location (lat/lon) field.

Changes made from version 3.60 to 3.70:

Fixed problem where tones 7-10 were incomplete.
Fixed problem where zooming would cancel measuring distance.

Changes made from version 3.50 to 3.60:

Allow position sending on GMRS channels.
Enabled GMRS on Canadian Rinos.
Fixed bug where turning GMRS off and then back on would not update Radio page.
Fixed potential problem with ring tones being used with position sending.

Changes made from version 3.40 to 3.50:

Updated to support transfer of proximity waypoints with MapSource.

Changes made from version 3.30 to 3.40:

Fixed problem that caused MGRS coordinates to occasionally display improperly in 'Big Number' mode.
Added support for RCV_CPO data.

Changes made from version 3.20 to 3.30:

Fixed potential memory corruption problem that could occur when tracking more than one WAAS satellite simultaneously.

Changes made from version 3.10 to 3.20:

Improved WAAS/EGNOS satellite selection algorithm to select the satellite with the most beneficial corrections given the unit's current position. Units will not use a WAAS/EGNOS satellite if the unit's current position is outside of a given WAAS/EGNOS satellite's service volume.
Fixed problem with incorrect waypoint date being displayed.

Changes made from version 3.00 to 3.10:

Minor display adjustments on Radio Setup and Tone Setup.
Fixed problem with potential lockup occurring in GMRS mode in version 3.00.

Changes made from version 2.40 to 3.00:

Increased the time between position sending from 10 to 30 seconds to comply with the latest FCC ruling.
Added polling feature to request a position from another Rino by pressing the CALL button with the contact highlighted on the Map page or through the menu option on the Contact page.
Added setup item to the Radio Setup page to disable poll response.
Moved Tone Setups to a separate page off of the Radio page menu.

Changes made from version 2.30 to 2.40:

Fixed potential problem with invalid codes being set after scanning current codes is complete.

Changes made from version 2.20 to 2.30:

Key-lock now allows use of CALL key.
Fixed problem with invalid CODE being set for Channel 22.
Always restore previously used CODE after scanning is done.

Changes made from version 2.10 to 2.20:

Allow user to disable power-on, power-off, and volume beeps by turning message beeps off.
Allow user to adjust microphone sensitivity for internal and headset microphones. Microphone adjustments may be found by going to the Radio Setup page, selecting the Menu, and selecting Set Sensitivity.
Improved audio in headset when transmitting with VOX.

Changes made from version 2.04 to 2.10:

Fixed problem with navigation fields and compass pointer sometimes going blank during navigation.
WARNING: This software update will clear user memory. Please backup important data to Mapsource.

System requirements

IBM-compatible PC running Windows 2000 or later operating system and an available Com 1, 2, 3, or 4 port.
PC Interface Cable for your GPS unit. The PC Interface Cable may be purchased through your local Garmin distributor or ordered direct from our Online Store.