Updates & Downloads


GPSMAP 162 software version 3.70

as of December 3, 2007


Download Factory Tide Settings
If MapSource data that does not contain tide points (e.g., U.S. Topo) was already loaded into your unit before you downloaded new unit software 3.03 or above, and you simply want to restore your pre-existing tide data, please download this file. This will replace the MapSource maps with tide data.
Download (1.35 MB)



Download Recommended MapSource US Tides Software
If you do not own a MapSource product which contains tides, but you do own another MapSource product, you can download and install this free MapSource U.S. Tides software. You must already own a MapSource product for this download to work. You can combine tide stations coverage from the Tides product with maps from other MapSource products and upload this to your unit.
Download (5.13 MB)


Download (1.19 MB)

View installation instructions and system requirements

Notes:


Change History

Changes made from version 3.60 to 3.70:

Changes made from version 3.50 to 3.60:

Changes made from version 3.40 to 3.50:

Changes made from version 3.30 to 3.40:

Changes made from version 3.20 to 3.30:

Changes made from version 3.10 to 3.20:

Changes made from version 3.05 to 3.10:

Changes made from version 3.04 to 3.05:

Changes made from version 3.03 to 3.04:

Changes made from version 2.61 to 3.03:

Changes made from version 2.60 to 2.61:

Changes made from version 2.52 to 2.60:

Changes made from version 2.50 to 2.52:

Changes made from version 2.13 to 2.50:

Changes made from version 2.12 to 2.13:

Changes made from version 2.11 to 2.12:

Changes made from version 2.10 to 2.11:

Changes made from version 2.01 to 2.10:

Changes made from version 2.00 to 2.01:


Installation Instructions

  1. It is recommended that you disable screen savers or other programs running on your PC while you go through the update process. Disruptions to the update process may render your GPS inoperable. If the transfer is interrupted, turn off the GPS and then turn it back on. Reboot your PC, go to step #9 and attempt the download again. GARMIN is not responsible for failed downloads of operating software to the GPS and factory resetting the GPS unit will fall under our Flat Rate Repair Policy.
  2. Click on "Download" and choose to save the file to your computer.
  3. Choose a location where you can easily locate the file by saving it to a location such as the "My Documents" folder or to "C:\".
  4. Once the download is complete, go to the location where you saved the file.
  5. Locate the downloaded file and double-click on it. This will launch the Win-Zip Self Extractor. This program compresses the data to allow for a faster download of the needed files.
  6. A program window will appear asking you where to "Un-zip" the files. This is by default C:\Garmin. You can change this location if you like. Be sure to note where the un-zipped files are going to allow you to find them!
  7. Click on the button labeled "Un-zip".
  8. Once the un-zip process is complete, click on the "Close" button to exit the Win-Zip Self Extractor.
  9. Open the C:\Garmin (or other folder where you un-zipped the files), locate the file named "Updater" and double click on it.
  10. Connect your GPS to your computer using a GARMIN PC Interface cable to an open serial port. Turn the GPS on, place it in Simulator mode (refer to your owner's manual for instructions) and verify that the Interface Mode (found under the Main Menu page, refer to your owner's manual for instructions) is set to GARMIN, GRMN, GRMN/GRMN, or Data Transfer/Host mode.
  11. Click on the "OK" button on the Updater program window to start the data transfer.

System requirements

  1. IBM-compatible PC running Windows XP or later operating system and an available Com 1, 2, 3, or 4 port.
  2. PC Interface Cable for your GPS unit. The PC Interface Cable may be purchased through your local Garmin distributor or ordered direct from our Online Store.